airbenchrest.ru
http://airbenchrest.ru/phpBB3/

.22LR Go Gauge & chamber
http://airbenchrest.ru/phpBB3/viewtopic.php?f=14&t=132
Страница 1 из 1

Автор:  spurlos69 [ 01 янв 2013, 17:45 ]
Заголовок сообщения:  .22LR Go Gauge & chamber

Возник вопрос по посадке патрона в патронник.
Чтобы установить ствол в Аншике 2013 http://www.riflebarrels.com/products/an ... arrels.htm рекомендуют использовать такую вот хрень http://www.riflebarrels.com/products/22_go_gauge.htm
Там написано про размер 0,043" это 1,0922мм я так понимаю что это величина закраины.
Перемерял все гильзы, что у меня есть, размер закраины составляет 1,0-1,02мм
Теперь вопрос: если установить ствол по этому Go Gauge, то патрон не будет садиться до конца, примерно на 0,1мм. Правильно ли это?
Этих Go Gauge полным полно, на каждый калибр http://www.midwayusa.com/find?newcatego ... ionid=1124
Вот видео, кто английский шарит, расскажите что там говорят.

http://www.youtube.com/watch?v=zqBQ3GcVHMo
http://www.youtube.com/watch?v=JODd4h_BWWI

Вот еще надо перевести:

Headspace gages are available in three different lengths, listed below, from shortest to longest:
- Go Gage: Go Gages match the minimum chamber dimensions allowable under SAAMI specifications. In order to accept SAAMI maximum ammunition, the rifle must be able to chamber the correct go gage.
- No-Go Gage: No-Go Gages are sized to the maximum recommended headspace dimensions. If a rifle will chamber the no-go gage, it may still be within specifications, or this could indicate excessive headspace. To determine if the rifle is safe to shoot, the chamber must be checked with the field gage.
- Field Gage: Field Gages correspond to the maximum safe headspace dimension. If a rifle will chamber a field gage, it should be inspected and repaired by a competent gunsmith prior to use.

Параллельное обсуждение: http://airgun.org.ua/forum/viewtopic.ph ... 00#p806300

Автор:  spurlos69 [ 02 янв 2013, 12:18 ]
Заголовок сообщения:  Re: .22LR Go Gauge & chamber

Как оказалось, различают несколько видов камер (chamber):
Sporting, Bentz, Match, Win 52-D
Отличаются они размерами, под каждый тип своя развертка и свой Go Gauge

Type______Length__Mouth Dia._Throat Dia._Taper @ Throat
Sporting____0.7751"____0.2307"____0.2270"
Bentz______0.6900"____0.2270"____0.2255"_____1.5° Taper
Match _____0.6876"____0.2267"____0.2248"
Win 52-D___0.5800"____0.2278"____0.2248"_____2.0° Taper

The "Ruger" 10/22 factory chamber is the "Sporting" chamber above.
The "Bentz" chamber is the 'match' chamber for semi-autos.
The "Match" chamber is for bolt actions.
The "Win M52-D" is a bolt action target rifle.

ИзображениеИзображение

Страница 1 из 1 Часовой пояс: UTC + 4 часа
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/